Get a Free Staircase Estimate in Minutes
Replacing worn treads, swapping out balusters, or adding a wall rail? Enter your stair basics and what you want done, and the price builds as you go, using the same rates I quote in St. Louis homes. Your price shows on the page before you give an email.
Stair & Rail Estimate
M Hope Carpentry · St. Louis
Your zip code tells you if you're in my service area.
Count each individual step. A standard single-flight staircase is usually 13–15 treads. How rail length is figured
$235 each. Includes proper anchoring regardless of post type.
A landing is any flat platform between flights. Each landing or turn typically adds a gooseneck fitting ($185 each). What's a gooseneck?
New install balusters are auto-calculated at 3 per LF of stair rail ($25 each). Use this section only if you need existing balusters replaced. Why 3 per foot?
$45/LF. Includes brackets and returns. Wall pads auto-calculated at 2 per run. About wall pads
$35/LF. Length is auto-calculated from your tread count. What's a skirt board?
$175 each. Includes scribing to wall conditions. Count defaults to your tread count above but can be adjusted. What scribing means
* This is a rough estimate for budgeting purposes. Rail lengths are calculated from tread count using standard stair geometry. Paced measurements are approximate. Final pricing is determined after a site visit.
Stair and railing pricing questions
How much does stair and railing work cost in St. Louis?
My labor rates:
- Stair rail: $55/LF
- Balusters, new install: $25 each (3 per foot of rail)
- Newel posts: $235 each, anchored properly whatever the post type
- Gooseneck fittings: $185 per landing or turn
- Baluster replacement on an existing rail: $75 each
- Wall handrail: $45/LF, brackets and returns included
- Wall pads: $15 each
- Skirt board: $35/LF
- Treads and risers: $175 per step, scribed to the wall
How do you get the rail length from my tread count?
I figure about 1.04 feet of rail per tread, so a 14-tread stair comes out to about 14.6 feet of rail. I measure the real length at the site visit.
Why are balusters added automatically?
Code requires gaps of less than 4 inches between balusters, which works out to about 3 per foot of rail. Any new rail gets them, so the estimate includes them.
What's a gooseneck fitting?
It's the curved rail piece that carries the handrail up and over at a landing or turn. Each landing or turn usually needs one.
I don't have a tape measure. How do I count paces?
Walk along where the landing rail would go, using normal steady steps, and count them. I figure 2.5 feet per pace.
What's a wall handrail run, and what are wall pads?
A run is one continuous section of handrail on the wall. Most stairs have one. Wall pads are the blocks the rail brackets mount to, and they have to land on studs, so I usually space them 4 to 5 feet apart depending on the framing. The estimate starts with 2 per run, and I set the real count at the site visit.
What's a skirt board?
It's the finished board that runs along the wall side of the stairs, where the treads meet the wall. Its length comes from your tread count.
What does replacing balusters involve?
I take out the old ones, redrill the rail and treads if the new ones need it, and set the new ones. That's $75 each.
If the new balusters won't land in the old holes, for example going from 1¼ inch wood balusters to ½ inch iron, the layout changes and the old holes get plugged. I use plugs of the same species as the tread or landing, match the grain as closely as I can, glue them in, and trim them flush with a chisel. I don't stain or finish the plugs. Plugging is extra labor, so I price it at the site visit.
What does scribing treads to the wall mean?
Walls are rarely straight, so I cut each tread to follow the wall's actual shape. That way there's no gap to caulk.
Is this a quote?
No. It's an estimate built from my standard rates, so you can see a realistic number before we meet. The final price is set after I see the job in person.
Does the price include materials?
No. The estimate covers labor only. Materials are separate, and I'm happy to talk through options when I see the job.
Why is there a $300 minimum?
Every job has a $300 service call minimum. It covers the drive, setting up my tools, and cleaning up, even when the job is one cut or one door. If your estimate comes in under $300, you'll still see your real numbers, then the minimum line, so nothing surprises you later.
How does the service area work?
I work out of south St. Louis city. That covers the whole city, North County, South County, and the suburbs inside 270. Near the edges, a job has to be big enough to be worth the drive. Enter your zip and the estimate tells you where you stand.
What happens after I send my estimate?
You get a copy by email. If you asked for a site visit, I'll reach out within 1 to 2 business days to set up a time from the availability you picked.